How to Prepare Walls Before Applying Distemper Paint

Steps To Follow Before Using Distemper Paint On Your Walls

A freshly painted wall can lose its charm faster than expected. There could be peeling near the corners, a dull patch under the tube light or even a fine hair-like crack that re-emerged on the newly painted surface. Most often such problems arise because of inadequate surface preparation before the painting began.

 

Walls collect dust, moisture, and small cracks over time. These problems, if left unchecked, would not allow the new coat of paint to adhere properly to the wall surface. Thus the surface preparation is as important as the selection of paint.

 

Before you start painting with distemper, make sure the surface of the wall is free from dampness and any loose paint, clean it thoroughly, and fill up any cracks in the surface. Prime where necessary and leave the surface to dry completely before applying subsequent coats of distemper.

 

Read on to understand how to prepare your walls for distemper paint and avoid common painting problems.

What Is Distemper Paint?

Distemper paint is a water-based, budget-friendly wall paint meant mainly for interior walls and ceilings. It dries to a smooth, matte finish and is ideal for bedrooms, living rooms and other interior walls and ceilings that need a fresh look on a budget.

 

Acrylic distemper is a modern variant of the traditional distemper. It uses acrylic polymers to help the paint stick to the surface better and last longer than traditional distemper.

Steps to Follow Before Painting Your Walls with Distemper

Once you have chosen the right distemper paint, follow these steps in order. Each step prepares the wall for the next one, so do not skip ahead.

  1. Inspect the Wall Surface

Start by checking the wall in good light. Check corners, around windows, on the ceiling and where water pipes are fixed to the wall.

 

This involves looking for any peeling paint, cracks, holes, damp areas, powdery surfaces, and any fungus or algae growth on the walls, especially in areas like the bathroom, kitchen, or near windows.

 

Do not paint over dampness as it will come back. Find out the cause of moisture such as leaking pipe, seepage from adjacent walls or from the roof and get it fixed before you start painting.

 

The wall should be tapped lightly to check for hollow sounds. It would indicate that the plaster has come off the wall and needs to be repaired before it applied.

  1. Clean the Walls Thoroughly

Dust and grease can also stop the paint from sticking to the surface of the wall. That is why the wall must be thoroughly cleaned before applying distemper paint.

 

Dust the surface of the wall using a dry cloth or soft brush. Wash greasy areas like kitchens with a mild detergent solution and wash with clean water. Allow the surface to dry completely before proceeding with further steps.

 

If there is fungus or algae, brush it off and clean the area with water. Do not paint over fungal growth, as it can spread under the new coat.

 

Keep the room well ventilated while cleaning and drying the wall. A dry wall will help the paint to stick to it better.

  1. Repair Cracks and Uneven Areas

Small cracks and holes in the wall can be filled with suitable wall putty or crack filling material depending on the size of the damage.

 

Use a putty knife to apply the filler into the crack. Allow it to dry as per the manufacturer’s instructions. Once dry, sand the surface until it matches the rest of the wall.

 

After sanding, wipe away the dust with a clean, dry cloth. This will ensure that the paint can spread evenly over the surface to give a smooth, even finish once it has dried.

 

For larger cracks, loose plaster or more extensive damage to the surface, you will need to get the help of a painter to carry out the repairs to the surface first.

  1. Check Whether Primer Is Required

A primer is not always necessary but is helpful to have in most cases. It acts as a base coat before the final coat of paint and helps to adhere to the wall better, seals any porous surfaces and helps to create a more even finish.

 

You may need primer if:

  • The wall is new or freshly plastered
  • The surface is highly absorbent
  • The old paint is chalky or uneven
  • You have applied wall putty
  • The distemper manufacturer recommends it

 

A freshly plastered wall needs time to cure before it can be painted. Let the wall dry completely before primer or paint is applied.

 

Astral Paints offers both water-thinnable and solvent-thinnable primers, so you can choose one based on the wall condition and the paint system you are using.

  1. Prepare Previously Painted Walls

Do not apply distemper paint on loose, flaking or powdery paint, even if the wall is in good condition.

 

Remove any loose paint with a scraper or wire brush. Sand any chalky residue from the previous paint. Then thoroughly clean the wall to remove any dust or grease.

 

Check whether the old coat of paint is compatible with the distemper paint you plan to use. Old finishes such as lime wash and powder distemper need to be scraped off the wall completely before repainting.

  1. Apply Distemper Paint Correctly

Read the instructions on the product before opening the pack. Different distemper products have different dilution ratios, drying times, and application methods.

 

In general:

 

  • Stir the paint well before use
  • Dilute it only as directed by the manufacturer
  • Use a clean brush, roller, or spray machine
  • Apply the first coat evenly
  • Let it dry before applying the next coat
  • Apply the second coat only if required

 

Astral Paints’ distemper range is designed to be easily applied with a brush, roller or spray for touch ups and re-painting of entire rooms.

 

  1. Allow the Surface to Dry Properly

Drying time matters at every stage. Make sure the wall is completely dry after you clean the surface, after you repair the wall, after you apply putty and after you apply primer on the wall.

 

The time taken by the putty and primer to dry varies from product to product and with the weather conditions. Refer to the instructions given on the product pack for the correct drying time.

 

Distemper paint usually needs a few hours between coats of paint. For acrylic distemper, the paint usually dries within 2-4 hours, but it is better to let the paint dry completely before you apply the next coat of paint.

 

Make sure the room is well ventilated during the drying process and do not touch or wash the wall too soon. This will help the paint to dry evenly and will reduce the chance of peeling or patchy areas.

Conclusion

Once you have prepared the surface for painting properly, painting with distemper paint is very easy. 

 

The surface must be damp free, clean, repaired for cracks, loose paint removed and primer applied where required. All layers must be allowed to dry completely before the next layer can be applied.

 

These steps would help in better bonding of distemper paint on walls and help in giving a smooth finish with even surface.

 

No matter whether you use traditional distemper paint or acrylic distemper paint, make sure you follow the manufacturer’s instructions.

 

For a smooth, washable matte finish, explore Styla Premium Acrylic Distemper from Astral Paints.

FAQs for Distemper Paint 

Q1. Can I apply distemper paint directly on a new wall?

 

The new wall has to be allowed to cure for several days before applying distemper paint. After the surface has dried completely, apply a coat of primer if required, and then apply distemper paint.

 

Q2. Is primer necessary before acrylic distemper?

 

As a general rule, primer is usually recommended for new plaster, putty and chalky surfaces. It helps the paint to adhere to the surface better and can help to provide a more even finish. However, follow the specific advice given by the manufacturer of the acrylic distemper that you have purchased.

 

Q3. What should I do if my wall has damp patches?

 

Do not paint over damp patches. First find and fix the source of moisture, such as a leaking pipe or seepage. Let the wall dry completely, repair the damaged area, and only then apply primer and distemper paint.

 

Q4. How many coats of distemper paint are usually needed?

 

Usually, two coats of distemper paint are required to achieve an even finish on most walls. However, this may vary depending on the condition of the surface, color of the paint and the instructions provided on the paint pack.

 

Q5. Can I paint over old distemper or lime wash?

 

Old lime wash or powder distemper must be scraped off prior to repainting. These types of paints can be chalky and may not adhere properly to the surface. It is best to clean, sand and prepare the surface prior to painting with a new coat.

Leave a Reply